Craps Table Sketchup file

I’ve had lots of requests for my sketchup file for the craps table project. I decided to just add a post with a link to get it.

Posted in Around the House, Craps, Hobbies, Woodworking • 4 Comments

12 Foot Craps Part 16

I got some more green diamond ends and cut them to height. I ended up just putting a few screws in them, in the valleys of the diamonds. It won’t affect the dice at all. You really can’t see them.

Posted in Around the House, Craps, Woodworking • 1 Comment

12 Foot Craps Part 15

I really started working hard on the padded rails this weekend. I bought a new air stapler and it works great! How did I ever do it any other way? This thing is awesome! At only $35 I should have bought one a long time ago.

Posted in Around the House, Craps, Woodworking • 2 Comments

12 Foot Craps Part 14

I’ve got the chip trays done, finally!

Time to start on the padded rail.

Posted in Around the House, Craps, Woodworking • Comment on this post

12 Foot Craps Part 13

After a close look at the casino craps table during my last visit, I decided the walls were too high on my table. I need to take about 2 inches off. The table bottom is about the right distance off the floor, but the chip trays and padded rail end up too high.

Posted in Around the House, Craps, Woodworking • 3 Comments

12 Foot Craps Part 12

I’ve got all the chip trays cut and dividers glued in.
Here is the table with all the chip trays screwed down and ready to stain.

Posted in Around the House, Craps, Woodworking • Comment on this post

12 Foot Craps Part 11

Over the last 2 weeks I finally got going on those corner chip rails. I’m finally done with the corners.

Posted in Around the House, Craps, Woodworking • 1 Comment

12 Foot Craps Part 10

I started on the corner chip rail pieces. These have proven to be a real pain in the butt.

Posted in Around the House, Craps, Woodworking • Comment on this post

12 Foot Craps Part 9

I’ve finished with the polyurethane and ready to place the layout on the table! I moved the old table out of the way and moved the new one in it’s place. Vacuumed the dust, and placed some flannel down and then the layout on top.

Posted in Around the House, Craps, Woodworking • 1 Comment

12 Foot Craps Part 8

I installed the T-nuts on the padded rail. I’m thinking about epoxying them as well. I don’t want them to push out after I finish the foam and vinyl.

Posted in Around the House, Craps, Woodworking • Comment on this post

12 Foot Craps Part 7

I know it’s not pretty, but I tried these metal straps to connect the three parts to the padded rail. I was going to use epoxy and some thin type of plastic, but saw these and thought I’d give it a try. With some really short screws, and doubled up, they seem to work fine. Hopefully they won’t be too noticeable under the padding, when leaned on.

Posted in Around the House, Craps, Woodworking • Comment on this post

12 Foot Craps Part 6

Time to start the padded rail. I have some OSB laying around that is long enough.
I put some down on the top, and try to figure this out. I made a jig that is 8″ long to draw a line for the outside dimension.

Posted in Craps, Woodworking • Comment on this post

12 Foot Craps Part 5

I need to cut into the table where the dealers would stand. They will need to be able to reach across the table. The table is so huge, they (me) will need all the help they can get.
Continue Reading

Posted in Craps, Woodworking • Comment on this post

12 Foot Craps Part 4

I started working on the top. I decided to use the 1×12 pine boards. I figured they would be sturdier than 1/2 plywood, and you could lean on them without a problem.

Posted in Craps, Woodworking • Comment on this post